STARLOG™

‹ Documentation

Moon Base User's Manual

Also available: StarLog Owner's Guide for Windows, StarLog Owner's Guide for Mac, Moon Ship User's Manual · Launch Day Quick Reference (PDF)

Welcome to the Moon BaseGetting to know your Moon BasePower and the microSD cardLaunch dayLightsBuzzerDuring a flightFinding your rocketBetween flightsDownloading flightsVerified flightsFirmware updatesPairingChecking your Moon BaseTroubleshootingSpecificationsSafety

Welcome to the Moon Base

The Moon Base is the ground station that sits at the launch site. It receives your Moon Ship's live data 10 times a second, shows the flight's stage on four lights and its buzzer, and saves a copy of every flight to its microSD card.

That second copy matters: if a recovery goes wrong and the rocket is lost, the flight is still on the ground.

This manual covers firmware V12. To see which version yours runs, plug it into StarLog and look at the Firmware line at the bottom of its panel.

Getting to know your Moon Base

Part What it's for
Power switch Turns the Moon Base on and off.
Four status lights ERROR (red), PAD (green), FLY (blue) and RECOVER (yellow), top to bottom.
Buzzer Follows the flight: a beep each second on the climb, a long tone at apogee, double beeps under the chute and three beeps when it lands.
microSD card slot Every flight is saved here, one file each.
USB-C port For downloading flights, firmware updates and power.
Beep-code key On the underside of the case, in flight order.

Power and the microSD card

Power. The Moon Base runs on a 2-cell (2S) LiPo battery, full at 8.4 V. Charge it on a 2S balance charger before launch day. It can also run from USB-C, for example from a power bank. Switch the Moon Base off whenever it's plugged into USB-C (StarLog, a computer or a power bank). USB powers it on its own, and with the switch on it would keep drawing on the battery, which the Moon Base doesn't charge. A LiPo run flat can be ruined.

The Moon Base doesn't warn you about its own battery, so start each launch day with it charged.

microSD card. Use a card of 32 GB or smaller, formatted FAT32. Push it fully in before switching on. A card is needed: without one, the ERROR light blinks rapidly and nothing is recorded.

Launch day

  1. Switch the Moon Base on before the Moon Ship, and set it where it has a clear line of sight to the pad. Raising it off the ground helps the radio.
  2. The four lights run once from top to bottom, then the buzzer chirps once: the Moon Base is ready. If instead ERROR blinks rapidly and there's no chirp, see Troubleshooting.
  3. Switch the Moon Ship on at the pad. Within a moment the green PAD light blinks slowly: the link is good.
  4. If ERROR is on solid, the Moon Ship's battery is low (3.40 V or less). Don't fly until it's charged.
  5. Launch. You don't need to watch the lights: the buzzer tells you each stage of the flight.

Lights

Light Pattern Meaning
All four Run once, top to bottom, at switch-on Light check, then 1 chirp when ready
PAD green Slow blink The link is good and the rocket is on the pad
FLY blue Solid In flight: the rocket has climbed past 33 ft (10 m)
RECOVER yellow Slow blink Landed. The flight is saved.
RECOVER and ERROR Both blinking Probably landed: the signal was lost on the way down, so the landing isn't confirmed yet
PAD green Pulses after landing Rocket finder: the Moon Base hears the rocket. Faster pulses mean a stronger signal
ERROR red Rapid blink Start-up fault: the microSD card or the radio didn't start
ERROR red Slow blink Signal lost (on the pad or in flight)
ERROR red Solid The Moon Ship's battery is low

When more than one problem applies, ERROR shows the most serious: a start-up fault, then signal loss, then low battery.

Buzzer

The buzzer follows the flight, in the same order as the key on the underside of the case.

Key Sound Meaning
● READY 1 chirp after the lights run Ready
● CLIMB One beep every second In flight, climbing
▬ APOGEE Long tone, 2 seconds Apogee
●● ●● CHUTE Quick double beep every second Coming down under the parachute
●●● LANDED Three beeps, pause, repeat, for about a minute Landed
●●●● LOST Four beeps, pause, repeat, for about a minute Signal lost, at any point in the flight

After a minute the landed and lost sounds stop, so the Moon Base isn't beeping on the table all afternoon. The lights keep showing what happened. When the Moon Base connects to StarLog it gives one short chirp, so you know which device StarLog is talking to.

During a flight

Moment What you'll see and hear
Lift-off PAD stops blinking, FLY comes on and the buzzer beeps every second.
Apogee A long tone for 2 seconds.
Descent FLY stays on and the buzzer double-beeps every second.
Landing FLY goes out, RECOVER blinks and the buzzer gives three beeps, pause, repeat, for about a minute.

If the signal drops. When no data arrives for 3 seconds during a flight, ERROR blinks slowly and the buzzer gives four beeps, pause, repeat, for about a minute. The Moon Base saves what it has so far. If the signal comes back, the climb or chute beeps start again, it carries on recording in the same file, and StarLog marks the gap. The Moon Ship's own log is complete either way.

Landing. The Moon Ship tells the Moon Base when it has landed. If that message doesn't get through, the Moon Base decides for itself once the altitude has stayed steady for 5 seconds.

Probably landed. If the signal is lost after lift-off and doesn't come back, the Moon Base works out when the rocket should be on the ground. Lost on the way down, it uses the last height and descent rate. Lost on the way up, it estimates the highest point the rocket could reach and allows for a slow descent. Either way it waits at least 1 minute and at most 10. After that, RECOVER and ERROR blink together and the landed sound plays. Walk toward the rocket with the Moon Base: as soon as it hears the rocket's recovery calls, the landing is confirmed and ERROR goes out. A signal lost while the rocket is still on the pad only shows signal lost.

Finding your rocket

After landing, the Moon Ship sends a short "I've landed" call about every 5 seconds, as well as chirping its recovery beacon. Each time the Moon Base hears a call, the green PAD light pulses. The stronger the signal, the faster it pulses.

  1. Carry the Moon Base toward where the rocket came down.
  2. Walk a few steps, then pause and watch the green light. Faster pulses mean you're getting closer.
  3. If the pulses slow down, turn slowly on the spot and head the way they speed up again.
  4. Close in, listen for the Moon Ship's chirp every 5 seconds.

This works even if the Moon Base lost the rocket before launch and missed the whole flight: the first recovery call it hears switches it to landed and starts the finder.

It's a warmer-or-colder guide, not a distance. Your body, tall wet grass and a rocket lying on its side all weaken the signal, so pause and turn slowly rather than rushing.

Between flights

After a landing, the Moon Base keeps listening for the rocket's recovery calls, for the rocket finder, and keeps showing RECOVER until you switch it off.

Switch the Moon Base off and on again before the next flight. Each power-up starts a new flight file, so flights never overwrite each other. A power-up that receives nothing doesn't leave an empty file behind.

Downloading flights

With StarLog

  1. Switch the Moon Base off, open StarLog and plug the Moon Base in with a USB-C data cable. USB powers it.
  2. StarLog finds it within a few seconds. The Moon Base gives one short chirp and the panel title changes to Connected to Moon Base.
  3. Click Download latest flight, or Download all to fetch every flight not yet on your computer.

You can plug the Moon Ship in at the same time. A Moon Ship / Moon Base switch appears at the top of the panel, and StarLog pairs the two logs of each flight under one flight number.

With a card reader

Switch the Moon Base off, take out the microSD card and put it in a card reader. In StarLog, click Import file… and choose the flight files (flight_01.csv, flight_02.csv and so on).

The Moon Base and the Moon Ship number their files separately, so their file numbers may not match. StarLog matches the two logs by their contents.

Freeing space: Erase Moon Base memory… in StarLog deletes the flights on the card, after saving any not yet on your computer if Save all flights to this computer first is ticked. It isn't allowed while a flight is in progress.

Verified flights

Every Moon Base has its own ID, such as MB-4D5E6F, and signs each flight it records. When you upload a flight to StarLog Flights, the site checks the signature. Flights from a registered Moon Base that haven't been changed are marked ✓ Verified.

Firmware updates

StarLog downloads new Moon Base firmware by itself and offers it when you plug the Moon Base in. Click Update firmware…, then Update, and keep the cable in until it restarts.

Pairing

Your Moon Base comes paired with your Moon Ship and ignores every other transmitter at the field. The pairing is kept through power-offs and firmware updates. To pair a replacement Moon Ship or Moon Base, email support@flystarlog.com.

Checking your Moon Base

If something seems wrong, or before an important launch, StarLog can test your Moon Base. Plug it in, click Preflight device… in StarLog's panel and keep it plugged in until the check is done.

StarLog checks the microSD card, the radio link to your Moon Ship (switch the Moon Ship on a few feet away; this takes 30 seconds), and lights each of the four lights and sounds the buzzer in turn, for you to tick as you see and hear them.

Each part gets a tick, a "!" for something to look at, or a cross. After fixing a problem (for example, switching the Moon Ship on), click Test again on that row. StarLog saves a report in Documents › StarLog › Device checks. If anything failed, click Email report: your email opens with the report filled in and addressed to support@flystarlog.com.

Troubleshooting

Problem Try this
No chirp after the lights run, ERROR blinks rapidly The microSD card is missing, loose, larger than 32 GB or not FAT32. Push it in fully, then switch off and on.
PAD never blinks Check the Moon Ship is switched on and chirped three times, and that there's a clear line of sight. A new or replacement device may need pairing.
ERROR solid on the pad The Moon Ship's battery is low. Charge it before flying.
Signal lost often Move the Moon Base higher and closer to the pad. Carbon fiber, metal and foil airframes block the radio; the Moon Ship's own log is still complete.
RECOVER and ERROR both blinking Probably landed, not confirmed. Walk toward the rocket with the Moon Base until the green light pulses; the landing is then confirmed.
The next flight isn't recorded The Moon Base was left on after the last landing. Switch it off and on before each flight.
StarLog says the SD card reader isn't working Push the card fully in, switch the Moon Base off and on, then click Reconnect.
StarLog can't find the Moon Base Use a data cable, then click Reconnect. USB powers the Moon Base, so leave its switch off.
Not sure it's working Plug it into StarLog and click Preflight device….

Specifications

Live radio 10 readings a second from its paired Moon Ship, 2.4 GHz digital radio
Log Time, altitude (ft and m), temperature, the Moon Ship's battery, highest altitude so far and flight stage
Storage microSD card, 32 GB or smaller, FAT32. One file per power-up, up to 99.
Signal-loss alarm No data for 3 seconds during a flight; sounds for about a minute
Rocket finder Green light pulses with signal strength from the rocket's recovery calls
Low-battery warning The Moon Ship's battery at 3.40 V or less
Power 2S LiPo (full 8.4 V), or USB-C
Connection USB-C to StarLog for Windows and Mac

Safety

Follow your club's range safety rules and the NAR or Tripoli safety code. The Moon Base only listens: it never controls ignition or recovery.

Questions? Email support@flystarlog.com with your Moon Base's ID and a sentence about what happened. We'll reply with what to do next.