STARLOG™

‹ Documentation

Moon Ship User's Manual

Also available: StarLog Owner's Guide for Windows, StarLog Owner's Guide for Mac, Moon Base User's Manual · Launch Day Quick Reference (PDF)

Welcome to the Moon ShipGetting to know your Moon ShipChargingFitting it in your rocketLaunch dayBeep codesWhat happens during a flightRecoveryDownloading flights with StarLogVerified flightsFirmware updatesPairingChecking your Moon ShipTroubleshootingSpecificationsSafety

Welcome to the Moon Ship

The Moon Ship is the flight computer that rides in your rocket. It measures altitude from air pressure 20 times a second and keeps a complete log of every flight in its own memory. It also radios the flight to your Moon Base 10 times a second, so a second copy is saved on the ground.

The Moon Ship only records. It never fires motors, ejection charges or recovery devices, so it can ride alongside any altimeter or deployment electronics you already fly.

This manual covers firmware V12. To see which version yours runs, plug it into StarLog and look at the Firmware line at the bottom of its panel.

Getting to know your Moon Ship

Part What it's for
Power switch Turns the Moon Ship on and off. Slide it toward the buzzer holes for ON, as the arrow on the case shows.
USB-C port In the end of the case. Used for charging, downloading flights and firmware updates. You never need to open the case to use it.
Buzzer Chirps when the Moon Ship is ready, beeps out fault codes and sounds a recovery beacon after landing.
Vent holes Let outside air reach the pressure sensor. Keep them clear.
Mounting ears For screwing the Moon Ship to a sled or tying it into the electronics bay.
Beep-code key Printed on the underside of the case, so the codes are always with you.

Charging

The Moon Ship runs on a built-in rechargeable battery (1S LiPo, 150 mAh).

  1. Slide the power switch to ON. The battery only charges while the switch is on.
  2. Plug a USB-C cable into the Moon Ship and into a computer, USB charger or power bank.
  3. Charge before every launch day, and top it up between flights if you can.

The Moon Base watches the Moon Ship's battery. If its ERROR light stays on solid on the pad, the Moon Ship's battery is low (3.40 V or less): charge it before you fly.

Don't charge an obviously damaged or swollen battery, and don't leave a charging device unattended in a hot car.

Fitting it in your rocket

Launch day

Altitude zero is set the moment you switch the Moon Ship on. Always switch it on at the pad, with the rocket on the rail, never at the prep table.

  1. Switch your Moon Base on first, so it records the whole pad wait.
  2. Put the rocket on the rail.
  3. Slide the Moon Ship's switch to ON and keep the rocket still for about 3 seconds while it measures the air pressure on the pad.
  4. Listen for 3 short chirps. That means it's calibrated and armed. A long, repeating beep means a fault (see Beep codes).
  5. Check the Moon Base: the green PAD light blinks slowly when it hears the Moon Ship.
  6. Clear the pad and launch.

Beep codes

Sound Meaning
● ● ● 3 short chirps at switch-on Calibrated and armed, ready to fly
▬ 1 long beep, repeating Altitude sensor fault. Don't fly.
▬ ▬ 2 long beeps, repeating Radio fault. Don't fly.
▬ ▬ ▬ 3 long beeps, repeating Memory fault. Don't fly.
● 1 chirp every 5 seconds Landed: recovery beacon (with a radio call to the Moon Base's rocket finder)
● 1 short chirp when StarLog connects StarLog is talking to this Moon Ship
Silence at switch-on Switched off, or the battery is flat. Charge it.

If a fault code sounds, switch off, wait a few seconds and switch on again. If it keeps sounding, plug the Moon Ship into StarLog, which explains the fault in plain words. Flights already stored can usually still be downloaded.

What happens during a flight

Moment What the Moon Ship does
On the pad Measures 20 times a second and keeps the last 2 seconds in memory. Nothing is saved yet, so testing on the bench never fills it with empty files.
Lift-off Once it is more than 33 ft (10 m) above the pad and climbing fast, it starts a new flight file, including the 2 seconds before lift-off. Carrying it up a hill or a ladder doesn't count as a launch.
Apogee Marked when the altitude has dropped 6.6 ft (2 m) below the highest point.
Descent Keeps logging every reading. The log is written to memory once a second, so a sudden power loss costs at most a second.
Landing When the altitude stays within 5 ft (1.5 m) for 5 seconds, it tells the Moon Base it has landed, closes the flight file and starts the recovery beacon: a chirp and a short radio call about every 5 seconds, for the Moon Base's rocket finder. Between calls the radio rests to save battery. Landing and recovery mode only ever follow a real launch. If it hasn't sensed a landing 20 minutes after launch (for example, hung up in a tree), it starts the recovery beacon anyway.

During a flight the Moon Ship ignores USB commands, so nothing can interrupt the log.

Recovery

  1. Walk toward where the rocket came down, carrying the Moon Base. Its green light pulses faster as you get closer (see Finding your rocket in the Moon Base manual). Close in, listen for a chirp every 5 seconds.
  2. Leave the Moon Ship switched on until you've found it, so the Moon Base can follow its recovery calls. Then switch it off to save the battery, unless you'll download straight away. The flight is already saved.
  3. Switch it off and on again before the next flight. After landing it stays in recovery mode, sending its recovery calls, until it's switched off. Switching on at the pad also sets a new altitude zero.

Downloading flights with StarLog

  1. Open StarLog on your computer.
  2. Plug the Moon Ship in with a USB-C data cable. Some cables only charge; if StarLog can't find it, try another cable.
  3. StarLog finds it within a few seconds. The Moon Ship gives one short chirp and the panel title changes to Connected to Moon Ship.
  4. Click Download latest flight, or Download all to fetch every flight not yet on your computer.

The Moon Ship's log is the complete one: every reading, 20 a second, with no radio gaps. StarLog pairs it with the Moon Base's copy of the same flight.

Memory: the Moon Ship holds up to 99 flights. When it's nearly full it stops starting new ones, and nothing already saved is lost. To make room, use Erase rocket memory… in StarLog, with Save all flights to this computer first ticked.

Verified flights

Every Moon Ship has its own ID, such as MS-1A2B3C, and signs each flight it records. When you upload a flight to StarLog Flights, the site checks the signature. Flights from a registered Moon Ship that haven't been changed are marked ✓ Verified.

Firmware updates

StarLog downloads new Moon Ship firmware by itself and offers it when you plug the Moon Ship in. Click Update firmware…, then Update, and keep the cable in until it restarts. It takes a few seconds.

Pairing

Your Moon Ship comes paired with your Moon Base, so a field full of transmitters never mixes up flights. The pairing is kept through power-offs and firmware updates. To pair a replacement Moon Ship or Moon Base, email support@flystarlog.com.

Checking your Moon Ship

If something seems wrong, or before an important launch, StarLog can test your Moon Ship. Plug it in, click Preflight device… in StarLog's panel and keep it plugged in until the check is done.

StarLog checks the battery and that it's charging (keep the power switch on), the altitude sensor, how quickly it responds (when it chirps, lift it straight up about 3 ft or 1 m and hold it there), the memory, the radio link to your Moon Base (switch the Moon Base on a few feet away; this takes 30 seconds) and the buzzer.

Each part gets a tick, a "!" for something to look at, or a cross. After fixing a problem (for example, switching the Moon Base on), click Test again on that row. StarLog saves a report in Documents › StarLog › Device checks. If anything failed, click Email report: your email opens with the report filled in and addressed to support@flystarlog.com.

Troubleshooting

Problem Try this
No chirps at switch-on Check the switch is toward the buzzer holes, then charge the battery.
Long beeps repeating See Beep codes. Switch off and on; if it continues, plug it into StarLog for an explanation.
The Moon Base's PAD light never blinks Check the Moon Ship chirped, the Moon Base is on, and they're within sight of each other. A new or replacement device may need pairing.
ERROR light solid on the Moon Base at the pad The Moon Ship's battery is low. Charge it before flying.
Altitude reads a few feet at rest The Moon Ship was switched on somewhere else. Switch it off and on at the pad.
The Moon Base loses the signal often The airframe may block the radio (carbon fiber, metal, foil). The Moon Ship's own log is still complete.
StarLog can't find the Moon Ship Use a data cable, wait for the chirps, then click Reconnect.
It won't arm after landing It's in recovery mode. Switch it off and on again.
Not sure it's working Plug it into StarLog and click Preflight device….

Specifications

Altitude sensor Precision barometric pressure sensor
Onboard log 20 readings a second: time, altitude (ft and m), temperature, battery and flight stage
Live radio 10 readings a second to its paired Moon Base, 2.4 GHz digital radio
Launch detection More than 33 ft (10 m) above the pad and climbing faster than 50 ft/s (15 m/s)
Recovery Chirp and radio call about every 5 seconds after landing; recovery starts anyway 20 minutes after launch
Apogee detection 6.6 ft (2 m) below the highest point
Landing detection Steady within 5 ft (1.5 m) for 5 seconds
Storage Up to 99 flights
Battery Rechargeable 1S LiPo, 150 mAh, charged over USB-C
Connection USB-C to StarLog for Windows and Mac

Safety

Follow your club's range safety rules and the NAR or Tripoli safety code. The Moon Ship never controls ignition or recovery deployment, and it doesn't replace a deployment altimeter.

Questions? Email support@flystarlog.com with your Moon Ship's ID and a sentence about what happened. We'll reply with what to do next.